"noah" wrote in message
...
On Thu, 7 Aug 2003 21:22:31 -0500, "JTC" wrote:
Update: Well I replenished the tilt fluid and the motor tilts up with no
problem. The motor will tilt down until it reaches the trim cylinder
piston
and stops. The trim goes down reeeaaaalllllyy slow. I don't understand
why. I am wondering if there were supposed to be three springs in the
valve
body instead of only two,,, or maybe I placed the spring over the wrong
ball
bearing. If anyone knows what I did wrong I would sure appreciate some
advise. I have read that the main things that go wrong the Force trim
units
are the o-rings in the trim and tilt cylinders and the "Point Check
Valve"
in the valve body. The point check valve is very difficult to get to and
I'd prefer not to screw with it as long as the motor will tilt even if it
bleeds down from the up position. I don't know how long the pump motor
will
list letting it wind the trim cylinder down taking about 2 minutes.
Well, if anyone has any advise I'd be very grateful.
JeffC
"JTC" wrote in message
...
I took the valve body off of the pump. Was covered in about 1/2 inch
of
sludge. Didn't find any O'Rings in the valve body but I wasn't able
too
take it completely apart. I did take it apart far enough to check the
bb's
and springs and gear inside. everything looked ok except for the
sludge
that I removed. I think maybe on of the springs was not in it correct
place
though. After I cleaned up everything and put it back together I
didn't
have enough trim fluid to refill the pump reservoir. I was only able
to
put
a little bit of fluid in. I attempted to tilt the motor and it did go
up
farther than it has been going but only about 4 inches. Then pump was
catching air since the fluid was low. Maybe I got it fixed. ??? The
only
other thing I am willing to change myself will be the o-ring in the
trim
cylinder. I don't know if losing pressure in the trim cylinder will
effect
the tilt cylinder and vice versa. I'll find out later today when I
work
on
it some more I guess.
JeffC
"JTC" wrote in message
...
I replaced O-Ring in the tilt cylinder with little improvement.
Guess I
have to move on to the pump.
"JTC" wrote in message
...
Well, I bought an assortment of O-Rings to replace the one in the
tilt
cylinder. If that doesn't work I'm going to take apart the pump to
see
what
can be replace in it.
Thanks for responding.
"Rural Knight" wrote in message
ink.net...
"JTC" wrote in message
...
My 125 Force Tilt/Trim always slowly let the motor down when
tilted
to
the
up position. Although annoying I lived with it for about a
year.
Last
week
the problem got worse. Now the motor will not tilt up unless I
assist
it
by
lifting the lower unit while using the trim button to tilt the
motor
up.
I
have examined the o-ring in the tilt cylinder and it looks
fine.
I
bought
a
replacement O-Ring anyway but it is the wrong size so I have to
get
another
one. However, I cant help but suspect the valve body on the
pump.
Does
anyone know what symptoms would indicate a problem with the
valve
body
verses the O-Rings in the tilt cylinder? And for those who
have
replaced
the O-Rings before, do they usually look damaged and mangled or
what?
Any advise is greatly appreciated.
The loss of pressure could be caused by any number of things,
but the piston/cylinder seal is probably the most likely cause of
the
problem. Other causes could be fluid reserve, value body,
pump impeller, etc.
There isn't any real way to tell if an O ring is bad, but a
reasonable
test is how hard it was to get the piston out of the cylinder. If
it
produced a reasonable vacuum when it came out, then it most
likely was good. The cylinder seal would show signs of leaking.
Other than that, it is an internal leak in the pump (more O
rings),
fluid level or a combination of same.
I would suspect internal leak though because you didn't say
anything about oil leaks.
Later,
Tom
Jeff- is it possible that the "down" problem is in the pivot points
on the motor (lacking grease), or that the trim piston is "dry" or a
little corroded? The problem may not be in the pump.
Make sure all zirc's are greased, and check out the trim piston. A
little hydraulic fluid on a rag will help lubricate it, or you can use
a little light teflon grease. Even minor corrosion can cause it to
"hang".
noah
Courtesy of Lee Yeaton,
See the boats of rec.boats
www.TheBayGuide.com/rec.boats
Thanks for the response noah. I will lubricate the pivot joint on the motor
as you suggest. However, I am sure that the problem is hydraulic. I
replaced the seals on the Point Check Valves in the valve body today. This
was supposed to stop leak down of the motor from the tilted up position.
When I first put the pump back on the motor it tilted up and down twice as I
was cycling the air out of the system then the motor quit tilting down.
(before it only the trim would not go down) now the trim wont go down
either, and the motor is still leaking down only allot slower now. I don't
know what to do at this point. Guess I'll be trying to find a rebuilt one
somewhere. I have seen a few places online to purchase a rebuilt one with
trade in of the old. approx $150 to $175 to do this if you can find
somebody who has one in stock.