In article ,
says...


In article . com,
"beaufortnc" wrote:

I'm prepping the bottom of my sailboat for barrier coat then ablative
bottom paint.

I'm thinking, however, that it might be a good idea to paint the prop
with something like Trinidad instead of ablative. It seems to me that
the ablative won't last long on the prop.

What's the conventional wisdom here?

I suspect something came up in the replies, but gave up when the thread
took a strange turn.

I've tried ablative, hard, "outboard" (TNT) and other options over the
years and have yet to find something that actually kept our prop clean
throughout the season.

I'm about to try something that scares the living dickens out of me, but
was recommended by the shop that installed our engine: NOTHING. No zinc,
no copper or tin-based paints. The theory is that the slight electrical
imbalance between the SS shaft and bronze prop will be sufficient to
keep both clean.

Since our shaft is isolated from everything else in the boat, the only
thing eating away half of our zincs each year is the SS/Bronze imbalance.

Put a donut zinc between the strut and the prop.

why don't you treat the problem and not the cause???
"Gogarty" wrote in message
...
In article
,
says...


In article
. com,
"beaufortnc" wrote:

I'm prepping the bottom of my sailboat for barrier coat
then ablative
bottom paint.

I'm thinking, however, that it might be a good idea to
paint the prop
with something like Trinidad instead of ablative. It
seems to me that
the ablative won't last long on the prop.

What's the conventional wisdom here?

I suspect something came up in the replies, but gave up
when the thread
took a strange turn.

I've tried ablative, hard, "outboard" (TNT) and other
options over the
years and have yet to find something that actually kept our
prop clean
throughout the season.

I'm about to try something that scares the living dickens
out of me, but
was recommended by the shop that installed our engine:
NOTHING. No zinc,
no copper or tin-based paints. The theory is that the
slight electrical
imbalance between the SS shaft and bronze prop will be
sufficient to
keep both clean.

Since our shaft is isolated from everything else in the
boat, the only
thing eating away half of our zincs each year is the
SS/Bronze imbalance.

Put a donut zinc between the strut and the prop.

"Gogarty" wrote in message

Put a donut zinc between the strut and the prop.

Uhhh, We HAVE had a zinc on the shaft and the MaxProp's hub as well.
Both get half eaten each year. Before the MaxProp & its zinc, we lost
the same half of the shaft zinc.

In article ,
"Boots" wrote:

why don't you treat the problem and not the cause???

We have no AC connection to dock power. There is no electrical
connection to the shaft or strut; the shaft is isolated by a plastic
drive-saver; electrical resistance between boat ground and shaft is
essentially infinite, so it's not from the battery.

It happened while we were in the mooring field.

Thus, I believe we solved what you believe is the problem already.

The *only* thing it can be is the difference in potential between bronze
and stainless steel.

OR... the potential difference between both steel & bronze and zinc, and
that's what I've been thinking for the past few years.

Truth be told, I *have* thought about switching out the shaft for
bronze. If the zinc still disappears, it's the zinc's problem as there's
nothing left. My only problem with this solution is that bronze bends
quite a bit easier than SS, and I'm more concerned about proper shaft
straightness and alignment than the loss of relatively cheap zincs.

--
Jere Lull
Xan-a-Deux ('73 Tanzer 28 #4 out of Tolchester, MD)
Xan's Pages: http://members.dca.net/jerelull/X-Main.html
Our BVI FAQs (290+ pics) http://homepage.mac.com/jerelull/BVI/

Jere Lull wrote:

"Gogarty" wrote in message


Put a donut zinc between the strut and the prop.


Uhhh, We HAVE had a zinc on the shaft and the MaxProp's hub as well.
Both get half eaten each year. Before the MaxProp & its zinc, we lost
the same half of the shaft zinc.

In article ,
"Boots" wrote:


why don't you treat the problem and not the cause???


We have no AC connection to dock power. There is no electrical
connection to the shaft or strut; the shaft is isolated by a plastic
drive-saver; electrical resistance between boat ground and shaft is
essentially infinite, so it's not from the battery.

It happened while we were in the mooring field.

Thus, I believe we solved what you believe is the problem already.

The *only* thing it can be is the difference in potential between bronze
and stainless steel.

OR... the potential difference between both steel & bronze and zinc, and
that's what I've been thinking for the past few years.

Truth be told, I *have* thought about switching out the shaft for
bronze. If the zinc still disappears, it's the zinc's problem as there's
nothing left. My only problem with this solution is that bronze bends
quite a bit easier than SS, and I'm more concerned about proper shaft
straightness and alignment than the loss of relatively cheap zincs.


Then you are left shopping for a stainless prop. Zincs may be
cheaper. Go without and watch the prop melt until thr money saved
on zinc offsets the cost of a prop. Or not. A thin insulating
bushing and washer between the shaft, prop and nut may serve you well.

In article ,
says...


"Gogarty" wrote in message

Put a donut zinc between the strut and the prop.

Uhhh, We HAVE had a zinc on the shaft and the MaxProp's hub as well.
Both get half eaten each year. Before the MaxProp & its zinc, we lost
the same half of the shaft zinc.

Well, of course the zinc gets eaten. That it gets assymetrically eaten
indicates a directional electrolysis current or whatever at your slip or
mooring. But that's odd too. Does your prop stop in the same position
every time?

But the point was preventing growth. Do you find that the zinc in close
proximity to the hub of the prop prevents or reduces growth on the hub? I
do.