Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #31   Report Post  
Steve
 
Posts: n/a
Default opinions sought for full-time cruiser Tools and Spares selection

My 12vdc service outlets are on a 15 amp breaker.. I have outlets all over
the boat for the drill, a 12 vdc soldering iron and a few other 12 gadgets..

Steve
s/v Good Intentions


  #32   Report Post  
Dazed and Confuzed
 
Posts: n/a
Default opinions sought for full-time cruiser Tools and Spares selection

Steve wrote:

My 12vdc service outlets are on a 15 amp breaker.. I have outlets all over
the boat for the drill, a 12 vdc soldering iron and a few other 12 gadgets..

Steve
s/v Good Intentions


ah.


--

Don't like the looks of nudists? Complain to the manufacturer.


  #33   Report Post  
Dazed and Confuzed
 
Posts: n/a
Default opinions sought for full-time cruiser Tools and Spares selection

Steve wrote:

My 12vdc service outlets are on a 15 amp breaker.. I have outlets all over
the boat for the drill, a 12 vdc soldering iron and a few other 12 gadgets..

Steve
s/v Good Intentions


ah.


--

Don't like the looks of nudists? Complain to the manufacturer.


  #34   Report Post  
Skip Gundlach
 
Posts: n/a
Default opinions sought for full-time cruiser Tools and Spares selection

"Bruce" wrote in message
...
A
You disappoint me. I was waiting for Skip to do a spreadsheet and

shopping
list of everything recommended, then buy it all and watch his boat sink

from
the excess weight. Boo hoo. I was going to sell him all the excess junk

we
hauled around for 3 years.
Bruce


LOL!!

Well, then, how about a list of what *not* to buy?? Yours should be a good
reference point, I'd expect.

That said, I'm aware of the relative availability of 'stuff' in the
Caribbean in general. However, I'd rather fix something that breaks than
hobble to someplace to have someone else do it, if I'm able and equipped. I
really don't want to carry more than I need, but, for example, a spare
starter and alternator and injectors + pump seems worthwhile, along with the
water pump parts and belts and the usual consumables.

I'd be very nervous without filters and a few other things, as well...

So, your comments on what you never used in 3 years would be welcome - as
have been the comments preceding! - thank you all, and keep them coming...

L8R

Skip, full survey on 16Feb

PS how's the rebuild coming?
--
"And then again, when you sit at the helm of your little ship on a clear
night, and gaze at the countless stars overhead, and realize that you are
quite alone on a great, wide sea, it is apt to occur to you that in the
general scheme of things you are merely an insignificant speck on the
surface of the ocean; and are not nearly so important or as self-sufficient
as you thought you were. Which is an exceedingly wholesome thought, and one
that may effect a permanent change in your deportment that will be greatly
appreciated by your friends."- James S. Pitkin


  #35   Report Post  
Skip Gundlach
 
Posts: n/a
Default opinions sought for full-time cruiser Tools and Spares selection

"Bruce" wrote in message
...
A
You disappoint me. I was waiting for Skip to do a spreadsheet and

shopping
list of everything recommended, then buy it all and watch his boat sink

from
the excess weight. Boo hoo. I was going to sell him all the excess junk

we
hauled around for 3 years.
Bruce


LOL!!

Well, then, how about a list of what *not* to buy?? Yours should be a good
reference point, I'd expect.

That said, I'm aware of the relative availability of 'stuff' in the
Caribbean in general. However, I'd rather fix something that breaks than
hobble to someplace to have someone else do it, if I'm able and equipped. I
really don't want to carry more than I need, but, for example, a spare
starter and alternator and injectors + pump seems worthwhile, along with the
water pump parts and belts and the usual consumables.

I'd be very nervous without filters and a few other things, as well...

So, your comments on what you never used in 3 years would be welcome - as
have been the comments preceding! - thank you all, and keep them coming...

L8R

Skip, full survey on 16Feb

PS how's the rebuild coming?
--
"And then again, when you sit at the helm of your little ship on a clear
night, and gaze at the countless stars overhead, and realize that you are
quite alone on a great, wide sea, it is apt to occur to you that in the
general scheme of things you are merely an insignificant speck on the
surface of the ocean; and are not nearly so important or as self-sufficient
as you thought you were. Which is an exceedingly wholesome thought, and one
that may effect a permanent change in your deportment that will be greatly
appreciated by your friends."- James S. Pitkin




  #36   Report Post  
Rosalie B.
 
Posts: n/a
Default opinions sought for full-time cruiser Tools and Spares selection

x-no-archive:yes

What I got from Bob this evening for a 1979 CSY 44 (which is about 50
feet if you count the bow pulpit and dinghy davits) fiberglass boat
with a Perkins 4-154 engine, 2 banks of four 6 volt batteries each,
four solar panels and a wind generator - no genset - cruising up and
down the ICW with some off shore legs.

He has:

cordless drill
4-1 screw driver and a whole bunch of other tools (tool box)
2 foot channel locks
strap wrenches
chain strap wrench
cable cutter (used for making jacklines out of cable and cutting the
staysail stay)
wrenches for the motor mounts
roto tool for routing and cutting, and a saber saw (he's built a
storage cabinet this winter and got my snorkel mask all full of
sawdust)
infrared thermometer - used on engine and refrigeration
spare throttle/clutch transmission cable (after ours broke when we
were anchored in the wilds of SC)
spare exhaust mixer elbow (after ours disintegrated being made of
aluminum - it lasted 20 some odd years though - had one made up by a
plumbing supply shop)
spare injectors, spare starter, spare alternator, spare electric fuel
pump, spare raw water pump, spare engine cooling pump, spare
alternator bracket (ours broke offshore), spare thermostats, several
fuel and several oil filters
spare caps for the dinghy chambers, and spare plug for the dinghy
although Bob lost the check valve off it today.
sewing machine - like Sailrite but that won't do actual sails
inverters for the sewing machine and tools, plus little ones for small
stuff
three changes of oil - change every 200 hours-mfg recommends oftener
but we use synthetic
rebuilt kit for the marine toilets and a handful of joker valves
spare batteries for the GPSs, battery operated lights etc.
spare hoses for everything (he thinks) and spare belts out the ying
yang

We have broken the water pressure pump and replaced it but don't have
a spare at the moment. But for what we are doing and where we are, we
can just go buy another one if we need it.


"Skip Gundlach"
wrote:

"Bruce" wrote in message
...
A
You disappoint me. I was waiting for Skip to do a spreadsheet and

shopping
list of everything recommended, then buy it all and watch his boat sink

from
the excess weight. Boo hoo. I was going to sell him all the excess junk

we
hauled around for 3 years.
Bruce


LOL!!

Well, then, how about a list of what *not* to buy?? Yours should be a good
reference point, I'd expect.

That said, I'm aware of the relative availability of 'stuff' in the
Caribbean in general. However, I'd rather fix something that breaks than
hobble to someplace to have someone else do it, if I'm able and equipped. I
really don't want to carry more than I need, but, for example, a spare
starter and alternator and injectors + pump seems worthwhile, along with the
water pump parts and belts and the usual consumables.

I'd be very nervous without filters and a few other things, as well...

So, your comments on what you never used in 3 years would be welcome - as
have been the comments preceding! - thank you all, and keep them coming...

L8R

Skip, full survey on 16Feb

PS how's the rebuild coming?


grandma Rosalie
  #37   Report Post  
Rosalie B.
 
Posts: n/a
Default opinions sought for full-time cruiser Tools and Spares selection

x-no-archive:yes

What I got from Bob this evening for a 1979 CSY 44 (which is about 50
feet if you count the bow pulpit and dinghy davits) fiberglass boat
with a Perkins 4-154 engine, 2 banks of four 6 volt batteries each,
four solar panels and a wind generator - no genset - cruising up and
down the ICW with some off shore legs.

He has:

cordless drill
4-1 screw driver and a whole bunch of other tools (tool box)
2 foot channel locks
strap wrenches
chain strap wrench
cable cutter (used for making jacklines out of cable and cutting the
staysail stay)
wrenches for the motor mounts
roto tool for routing and cutting, and a saber saw (he's built a
storage cabinet this winter and got my snorkel mask all full of
sawdust)
infrared thermometer - used on engine and refrigeration
spare throttle/clutch transmission cable (after ours broke when we
were anchored in the wilds of SC)
spare exhaust mixer elbow (after ours disintegrated being made of
aluminum - it lasted 20 some odd years though - had one made up by a
plumbing supply shop)
spare injectors, spare starter, spare alternator, spare electric fuel
pump, spare raw water pump, spare engine cooling pump, spare
alternator bracket (ours broke offshore), spare thermostats, several
fuel and several oil filters
spare caps for the dinghy chambers, and spare plug for the dinghy
although Bob lost the check valve off it today.
sewing machine - like Sailrite but that won't do actual sails
inverters for the sewing machine and tools, plus little ones for small
stuff
three changes of oil - change every 200 hours-mfg recommends oftener
but we use synthetic
rebuilt kit for the marine toilets and a handful of joker valves
spare batteries for the GPSs, battery operated lights etc.
spare hoses for everything (he thinks) and spare belts out the ying
yang

We have broken the water pressure pump and replaced it but don't have
a spare at the moment. But for what we are doing and where we are, we
can just go buy another one if we need it.


"Skip Gundlach"
wrote:

"Bruce" wrote in message
...
A
You disappoint me. I was waiting for Skip to do a spreadsheet and

shopping
list of everything recommended, then buy it all and watch his boat sink

from
the excess weight. Boo hoo. I was going to sell him all the excess junk

we
hauled around for 3 years.
Bruce


LOL!!

Well, then, how about a list of what *not* to buy?? Yours should be a good
reference point, I'd expect.

That said, I'm aware of the relative availability of 'stuff' in the
Caribbean in general. However, I'd rather fix something that breaks than
hobble to someplace to have someone else do it, if I'm able and equipped. I
really don't want to carry more than I need, but, for example, a spare
starter and alternator and injectors + pump seems worthwhile, along with the
water pump parts and belts and the usual consumables.

I'd be very nervous without filters and a few other things, as well...

So, your comments on what you never used in 3 years would be welcome - as
have been the comments preceding! - thank you all, and keep them coming...

L8R

Skip, full survey on 16Feb

PS how's the rebuild coming?


grandma Rosalie
  #38   Report Post  
Bruce
 
Posts: n/a
Default opinions sought for full-time cruiser Tools and Spares selection

What not to bring is a better idea. I was going to take spare injectors
until the guy who owned a diesel repair facility is St Thomas told me that a
spare would last 6 months at best before the tip would go bad. I didn't
take any and I never needed one. My advise is to go through the boat and
write down every piece of gear you have on the boat and pretend it is going
to break. Go shop for replacements. If you can easily find a replacement
here, you can find it in the Island chain. Budget Marine is generally
better stocked than West. If you can't, then start watching ebay for a
spare. A friend came through yesterday with a Simrad Autopilot problem. It
was going to cost him $750 for a circuit board. This is the kind of stuff
to look for when filling up hiddy holes. If you have a watermaker, then
take a spare membrane but not a rebuild kit for the pump.
Congradulations on you new boat...it has been a long road.

On rebuilding the Endeavour, I went to replace the headliner and found that
the moorons who built the boat, installed all the headliner wood in the
coach roof...stapled in the headliner and then mated the top to the hull.
All the wood is running over the top of the bulkheads and you couldn't take
down the headliner. I developed a technique to cut the wood out and will
post photos of the process at a later date on my website. After I get the
wood removed, I am going to reengineer the coach roof by adding stiffeners
and the Velcro the headliner in place in 2' sections. The roof of a 43 is
like a diving board.
Later
Bruce


  #39   Report Post  
Bruce
 
Posts: n/a
Default opinions sought for full-time cruiser Tools and Spares selection

What not to bring is a better idea. I was going to take spare injectors
until the guy who owned a diesel repair facility is St Thomas told me that a
spare would last 6 months at best before the tip would go bad. I didn't
take any and I never needed one. My advise is to go through the boat and
write down every piece of gear you have on the boat and pretend it is going
to break. Go shop for replacements. If you can easily find a replacement
here, you can find it in the Island chain. Budget Marine is generally
better stocked than West. If you can't, then start watching ebay for a
spare. A friend came through yesterday with a Simrad Autopilot problem. It
was going to cost him $750 for a circuit board. This is the kind of stuff
to look for when filling up hiddy holes. If you have a watermaker, then
take a spare membrane but not a rebuild kit for the pump.
Congradulations on you new boat...it has been a long road.

On rebuilding the Endeavour, I went to replace the headliner and found that
the moorons who built the boat, installed all the headliner wood in the
coach roof...stapled in the headliner and then mated the top to the hull.
All the wood is running over the top of the bulkheads and you couldn't take
down the headliner. I developed a technique to cut the wood out and will
post photos of the process at a later date on my website. After I get the
wood removed, I am going to reengineer the coach roof by adding stiffeners
and the Velcro the headliner in place in 2' sections. The roof of a 43 is
like a diving board.
Later
Bruce


  #40   Report Post  
Steve
 
Posts: n/a
Default opinions sought for full-time cruiser Tools and Spares selection


"Bruce" wrote in message
...
What not to bring is a better idea. I was going to take spare injectors
until the guy who owned a diesel repair facility is St Thomas told me that

a
spare would last 6 months at best before the tip would go bad. I didn't
take any and I never needed one.


Now that is a bunch of BS.. I'm amazed that any mechanic would make such a
statement..

A new or rebuilt injector is filled with diesel or calibration fluid and
once you seal it up in oiled rags in a zip lock bag it will last for ever..
There is just no way it can deteriorate. The spare injector I carryed around
on my last boat (same engine as now) is in perfect condition after 15 years
in storage.

Steve
s/v Good Intentions



Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is Off
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
opinions sought for full-time cruiser Tools and Spares selection Skip Gundlach Boat Building 32 February 9th 04 11:56 PM


All times are GMT +1. The time now is 03:03 PM.

Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 BoatBanter.com.
The comments are property of their posters.
 

About Us

"It's about Boats"

 

Copyright © 2017