Hi Guys,

I have a Furuno 6100 and a Magellan 315. I have the cable required got the
two units, but am not sure how to link the two. Any ideas from anyone?

Thanks
Alan

My Garmin uses a cable with a DB9 connector to connect to my PC. I added a
DB9 connector to the bare end of the Furuno cable. I connect the two DB9s so
the Garmin talks to the Furuno instead of my PC.
The only problem I've had is with corrosion of the DB9 I added to the Furuno
cable. I will replace it, and fill it up with even more silicone seal before
I screw the two halves together, and use even more dielectric grease on the
connecor pins.


"Grumpy" wrote in message
...
Hi Guys,

I have a Furuno 6100 and a Magellan 315. I have the cable required got the
two units, but am not sure how to link the two. Any ideas from anyone?

Thanks
Alan

No problem with that but the Furuno has TD-A, TD-B, RX-A, RX-B, do I just
use 1 set ie. A or B?

"William G. Andersen" wrote in message
news:jF%7c.1413$Rh.1173@fed1read05...
My Garmin uses a cable with a DB9 connector to connect to my PC. I added a
DB9 connector to the bare end of the Furuno cable. I connect the two DB9s
so
the Garmin talks to the Furuno instead of my PC.
The only problem I've had is with corrosion of the DB9 I added to the
Furuno
cable. I will replace it, and fill it up with even more silicone seal
before
I screw the two halves together, and use even more dielectric grease on
the
connecor pins.


"Grumpy" wrote in message
...
Hi Guys,

I have a Furuno 6100 and a Magellan 315. I have the cable required got
the
two units, but am not sure how to link the two. Any ideas from anyone?

Thanks
Alan

"Grumpy" wrote in message
...
No problem with that but the Furuno has TD-A, TD-B, RX-A, RX-B, do I just
use 1 set ie. A or B?

Furuno --- Magellan
TD-A ----- RX
Ground ----- Ground
RX-A ----- TX
RX-B ----- Ground

TD-B is left unconnected.

Meindert

My friend u are a gentleman, many thanks
Will give it a go a bit later tonight

Regards

Alan

"Meindert Sprang" wrote in message
...
"Grumpy" wrote in message
...
No problem with that but the Furuno has TD-A, TD-B, RX-A, RX-B, do I
just
use 1 set ie. A or B?

Furuno --- Magellan
TD-A ----- RX
Ground ----- Ground
RX-A ----- TX
RX-B ----- Ground

TD-B is left unconnected.

Meindert

"Grumpy" wrote in message
u...

My friend u are a gentleman, many thanks
Will give it a go a bit later tonight

Do let us know if it did work out ok :-)

Meindert

and if it doesn't, call Magellan.
I tried using Furuno's web site info and it didn't work. I went to Garmin
and found exactly what I needed. I think all three companies are very
helpful and take good care of their customers.

"Meindert Sprang" wrote in message
...
"Grumpy" wrote in message
u...

My friend u are a gentleman, many thanks
Will give it a go a bit later tonight

Do let us know if it did work out ok :-)

Meindert

"William G. Andersen" wrote in message
news:_%j8c.2805$Rh.1202@fed1read05...
and if it doesn't, call Magellan.
I tried using Furuno's web site info and it didn't work. I went to Garmin
and found exactly what I needed. I think all three companies are very
helpful and take good care of their customers.

And you can also take a look at www.shipmodul.com/en/connections.html
This page describes all sort of combinations with single-ended (signal vs.
ground) and differential (+/-, A and B) connections. And wherever you read
'multiplexer' you can fill in any NMEA capable device.

Meindert