On Fri, 13 May 2005 18:50:45 -0400, "ToneJohn" wrote:

Well after running for a while the exhaust elbow are warm/hot but i can hold
my hand there after running for about 10-15mins....


"John H" wrote in message
.. .
On Thu, 12 May 2005 22:11:59 -0400, "ToneJohn" wrote:


"John H" wrote in message
...
On Wed, 11 May 2005 23:21:25 -0400, "ToneJohn" wrote:

I have a 94 Chaparral 350MAG w/ an Alpha one. I recently started it up
for
the season and encountered the following and need advice / help on
possible
cause:

1) When running with earmuffs the water is flushed/spit out only on one
side of the lower unit. If i remember correctly last year it was
flushed
out on both sides of the lower unit. I never really paid much attention
but
for some reason i remember it coming out on both sides. Any suggestions
on
possible causes? I keep my boat dry docked and cover the lower unit
during
the winter.

2) With the earmuffs attached and shift into reverse, i heard a
constant
"slapping" noise coming for the lower unit area. Doesn't sound like
metal.... But when i give it more juice in reverse it goes away, but
then
comes back when i idle slow in reverse.

Things i did before the winter: Flushed and Fogged and backfilled with
Antifreeze.
Things i did in the last few weeks: Changed lower unit lube (old oil
lube
was clear). Changed the impeller. Greased Prop Shaft.
I did all of the above with someone who knows what there doing

Any suggestions are greatly appreciated, before i bring it to the local
marine and get robbed

THanks !! !

-Matt


My water was coming out of only one side, starboard, for a couple weeks.
The
mechanic at the marina said 'twas no big deal. Then my starboard exhaust
hose
started burning on me while out on the water. Had holes in the exhaust
hose.
Turns out the riser was plugged.

Take off the manifolds and risers and check them out. If the manifolds
and
risers haven't been replaced in 11 years, you've been lucky. Mine lasted
7
in
the Chesapeake Bay. Most folks say 10 years is max for fresh water.

Don't wait for a bigger problem to develop!

--
John H

"All decisions are the result of binary thinking."



I know that one manifold was replaced last year. but the problem side one
hasn't. Now if i take the Exhaust elbow off how do i know if it is "bad"
i
know when i have taken the hoses off it is very brigth orange/rust color..
any suggestions or sites? I would like to try and do this myself because
my
local marine takes forever this time of year...


It's hard to believe that someone would replace one manifold and riser and
not
the other set, especially after 10 years. If I were you, I'd just order
the
parts and replace the manifold and riser on the bad side. Once my manifold
and
riser were off, I couldn't see a 'plug', but no water was coming through!

After replacing the parts water was coming through the exhaust. Try
feeling the
risers while the engine is running. If one feels much hotter than the
other,
then that's where your problem is. You should be able to place your hands
on
both without getting burned.
--
John H

"All decisions are the result of binary thinking."


Well, now you've got me stumped. If no water is coming thru the exhaust, then
I'm wondering what is keeping the riser cool. Are you letting the engine get to
operating temp?

I don't know. Hopefully some of the able mechanics in the group will have some
more advice. Me, I'd be taking the manifold and riser off. Replacing them can be
done by yourself, but it's easier if someone holds the manifold while you get
the bolts started. I tied a piece of rope around it, wrapped the rope around my
neck and raised and lowered my back to move the manifold up and down.
Cumbersome, but it worked.
--
John H

"All decisions are the result of binary thinking."

WEll one of the mechanics at a local marine mentioned it might be the
exhaust flap. and it might be forced shut causing the water to exit only to
one side, he said that at regular earmuffs temperature it wouldn't make a
diff but after operating it on the water it would overheat... i'm brining it
to the marine on wed... let the prof. handle the problem...


"John H" wrote in message
...
On Fri, 13 May 2005 18:50:45 -0400, "ToneJohn" wrote:

Well after running for a while the exhaust elbow are warm/hot but i can
hold
my hand there after running for about 10-15mins....


"John H" wrote in message
. ..
On Thu, 12 May 2005 22:11:59 -0400, "ToneJohn" wrote:


"John H" wrote in message
m...
On Wed, 11 May 2005 23:21:25 -0400, "ToneJohn"
wrote:

I have a 94 Chaparral 350MAG w/ an Alpha one. I recently started it
up
for
the season and encountered the following and need advice / help on
possible
cause:

1) When running with earmuffs the water is flushed/spit out only on
one
side of the lower unit. If i remember correctly last year it was
flushed
out on both sides of the lower unit. I never really paid much
attention
but
for some reason i remember it coming out on both sides. Any
suggestions
on
possible causes? I keep my boat dry docked and cover the lower unit
during
the winter.

2) With the earmuffs attached and shift into reverse, i heard a
constant
"slapping" noise coming for the lower unit area. Doesn't sound like
metal.... But when i give it more juice in reverse it goes away, but
then
comes back when i idle slow in reverse.

Things i did before the winter: Flushed and Fogged and backfilled
with
Antifreeze.
Things i did in the last few weeks: Changed lower unit lube (old oil
lube
was clear). Changed the impeller. Greased Prop Shaft.
I did all of the above with someone who knows what there doing

Any suggestions are greatly appreciated, before i bring it to the
local
marine and get robbed

THanks !! !

-Matt


My water was coming out of only one side, starboard, for a couple
weeks.
The
mechanic at the marina said 'twas no big deal. Then my starboard
exhaust
hose
started burning on me while out on the water. Had holes in the exhaust
hose.
Turns out the riser was plugged.

Take off the manifolds and risers and check them out. If the manifolds
and
risers haven't been replaced in 11 years, you've been lucky. Mine
lasted
7
in
the Chesapeake Bay. Most folks say 10 years is max for fresh water.

Don't wait for a bigger problem to develop!

--
John H

"All decisions are the result of binary thinking."



I know that one manifold was replaced last year. but the problem side
one
hasn't. Now if i take the Exhaust elbow off how do i know if it is
"bad"
i
know when i have taken the hoses off it is very brigth orange/rust
color..
any suggestions or sites? I would like to try and do this myself
because
my
local marine takes forever this time of year...


It's hard to believe that someone would replace one manifold and riser
and
not
the other set, especially after 10 years. If I were you, I'd just order
the
parts and replace the manifold and riser on the bad side. Once my
manifold
and
riser were off, I couldn't see a 'plug', but no water was coming
through!

After replacing the parts water was coming through the exhaust. Try
feeling the
risers while the engine is running. If one feels much hotter than the
other,
then that's where your problem is. You should be able to place your
hands
on
both without getting burned.
--
John H

"All decisions are the result of binary thinking."


Well, now you've got me stumped. If no water is coming thru the exhaust,
then
I'm wondering what is keeping the riser cool. Are you letting the engine
get to
operating temp?

I don't know. Hopefully some of the able mechanics in the group will have
some
more advice. Me, I'd be taking the manifold and riser off. Replacing them
can be
done by yourself, but it's easier if someone holds the manifold while you
get
the bolts started. I tied a piece of rope around it, wrapped the rope
around my
neck and raised and lowered my back to move the manifold up and down.
Cumbersome, but it worked.
--
John H

"All decisions are the result of binary thinking."